Health and safety interview questions and answers

Health and safety interview questions and answers

55. Safety rules when using ladders?

1. The foot wear is not greasy, oily and muddy and has a good grip on the rungs.
2. When climbing or coming down a ladder should be face the ladder side and had on with both hand.
3. Carry light tools in pockets in a shoulder bag.
4. Hold on with at least new hand if use of both hands then, use safety belt
5. Never climb higher than the third rung from the top on straight or second tired from the top on extension ladder.
6. Step ladder must be fully open and the divider locked
7. Metal ladder shall not be used near electrical equipments.
8. Metal ladder shall not be place on firm footing and at angle of 75
9. Any ladder found defect in any way should be marked do not use
10. Ladder shall not be placed on a box or drum.
11. Rubber protection on head and heel of a ladder is necessary.

56. Safety rules insuring oxygen cylinders?

1. Oxygen cylinders should not be kept near combustible materials.
2. Oxygen cylinders should not be handled with grassy hands or gloves.
3. Oxygen cylinders and their fittings should not be tested with oil based soap solution.
4. Oxygen cylinders and other combustible gas cylinders should not be stored together.
5. The top cover of the cylinder should be kept in position and screwed safety when not in use.
6. Cylinders should not be used as rollers for moving materials
7. Oxygen must not be use for ventilating confined spaces.
57. Safety rules in using compressed air?
1. Only authorized persons should used compressed air.
2. The body or clothes should not be cleaned with compressed air.
3. Compressed air hose pipes should not be placed across passage ways
4. Leakage of compressed air should not be tested with hands.
5. While working with tools run by compressed air safety shoes are to be used.
6. The tools should not be kept on position when not in use.
58. Handling of compressed gas cylinders?
1. They are not to be dragged or dropped
2. They should be stored in dry and well ventilated places
3. Chins and slings should not be used for lifting cylinders.
4. the caps of the cylinders should not be removed when they are not the use.
5. Cylinders should not be stored near hot sources
6. Acetylene cylinders should not be stored horizontally
7. Empty cylinders and fully cylinders should be stored separately
8. Leakage cylinders removed to open space and release the gas without getting ignited.
Health and safety interview questions and answers  59. Storage of gas cylinders.
1. Cylinders should stored in a safe, dry and well ventilated store
2. Oxygen cylinders should be stored horizontally and acetylene cylinders shall be stored vertically.
3. The standing cylinders should be secured properly avoid falling.
4. Flammable gas shall be stored at least 50 feet away from another building
5. Oxygen cylinder shall never be stored necessary flammable gas cylinder
6. Empty cylinder shall be identified by marking with a chalk (MT) and checked for damage before returning to suppliers.
7. Cylinders should not be kept as supports.
Health and safety interview questions and answers 
60. Give a brief note about crane and LE?
1. Only authorized and competent person should operated cranes
2. The correct sling must be used for the load to be lifts
3. Lifting equipment must be certified from competent authority and mark with its SWL
4. Never be used for loads excess of its SWL
5. Cables and slings must be padded when passing over sharp edges of equipments
6. Check the condition of the ground before parking the crane and use out riggers
7. All moving parts must be guarded
8. Uncertified chains, ropes, slings and hooks should not be use
9. All slings to be inspected by third party inspectors
10. Never stand or work under a suspended load
11. Place the out riggers on firms ground
12. Guide ropes shall be used to control swing of lifted material
13. Never operate the crane at the time of speed wing
14. Lifting over live equipment should not be encouraged
15. The crane should under go periodical maintenance as per manufactures
61 Give brief note about fork lift truck?
1. Check breaks, lift tilt and tires.
2. Check the stability of load before moving it
3. Never leave your fork lift truck un-attend with motor running
4. Never park fork lift truck on passage way
5. Never drive with wet or greasy hands
6. Always drive with a safe speed and slow down at turning point
7. When driving without load forks about 6 inches above the floor or ground
8. Never operate trunk in gaseous area
9. Never carry a load so high that you can not head, If necessary operate truck in reverse
10. Avoid carrying lose materials on forks
11. Never allow one to go under elevated loads
12. Warn other employees to stand clear when staking or removing materials
13. Exhaust pipe should have flame arrestor
14. Fork should be lowered to the floor when the truck is unattended
15. Stay alert t all times
Health and safety interview questions and answers 
62 Give a brief about grinding?
1. Proper wheel shall be used a per the grinding M/c’s specification
2. All the grinding M/c’s shall be used with wheel guard
3. Grinding cables shall not mingle with welding cables
4. All the cables shall be protected from damage
5. Provide face shield with safety helmet
6. Never use fracture wheel
7. Excessive tighting of maintaining is dangerous
8. All guards should be in position before the machine operated
9. The speed of the grinding should match in the speeds of the grinding machines
10. Only skill person should be handle this work
11. Testing of wheel is necessary
63 Describe about vehicles and plants?
1. All vehicles requiring security vehicles pass
2. All drivers should have valid driving licence
3. Drivers should not use fork lift trucks for carrying passengers
4. All traffic regulations and speed limit should be strictly followed in side the plant area
5. All vehicles area in a road worthy condition
6. Vehicles park in the operation area must always unlocked with in ignition key in position
64 Precaution of excavation?
1. Excavation area should be suitable barricade
2. Put sign boards lights and flags
3. Avoid heavy vehicle coming near the sides
4. PPE like helmet, safety shoes should be used
5. Keep the excavated soil at least 5 feet distance
6. Excavated sides should be sloped bake to a safe angle
7. Hand excavation should be done at the present of UG pipes or cables place
8. Cutting shall be done from top to bottom
9. All narrow trenches 4 feet or more deep shall be supplied at least one ladder
10. While excavating on the slope on the slope whose height is over 10 feet men should use safety belts
65 What are advantages of JSA? ( Job safety Analysis)
1. It helps to identify hazards and prevent accident
2. It helps to establish safe work method, working conditions and suitable plant safety rules
3. It helps to asses the safety training four heading can be used for JSA.
4. It helps to inspection the plant
a) Name of operation for JSA
b) Description of the operation
c) Hazards
d) Precautions
66 What is tool box talk?
1. Job related safety aspects
2. Job related hazards / risk
3. Control / preventive measure
4. Adequacy of PPE’s / condition
5. Following safety rules / procedures
6. Safe work procedures / methods
67 Describe different types of hazards?
1. Mechanical hazards — in adequately guarded machines parts
2. Chemical hazards — of toxemic gasses, vapours, fumes, smoke in dust.
3. Electrical hazards : in adequately insulated line wires
4. Fire hazards – chemical reaction, electrical Arcs
5. Radiation hazards – dazzing light in fraved rays ultra violet rays
6. Pollution — water pollution & noise pollution
68 What is inspection?
1. Inspection means to fin out hazards according to checklist prepared with reference to the department operations by the people who are familiar with the plant.


For more Question 

  69 to 81

    Previous 1  2  3  4  5  6  7  8  9  Next